Limitorque LY 1001 Series Installation And Maintenance Manual Download Page 48

Page: 48 / 63

7-6

LY Installation and Maintenance for LY 1001, LY 2001 and LY 3001

LMAIM1501

Remove Input Worm Motor Pinion Assembly

10. Remove Input Worm Motor Pinion Assembly (piece #52, 53, 124, and 31).

Remove Worm Shaft Assembly

11. Remove four Screws (piece #61) and four Lockwashers (piece #62) to remove Bearing Cap (piece #5).

12. Remove Bearing Cap (piece #5) and O-Ring (piece #135).

13. Rotate Worm Shaft Assembly counterclockwise. The Worm Shaft Assembly should travel out of the Housing.

Once it has reached the end-of-travel, pull the remaining Worm Shaft Assembly out; Clutch Sleeve (piece #13)

will slip off the Worm Shaft Assembly. In the event that the Worm is stripped, the Worm Shaft Assembly will

need to be completely replaced.

NOTE: If Light Spring Pack or Heavy Spring Pack replacement is necessary, contact your Limitorque

authorized dealer or the Limitorque Service Department for a complete Worm Shaft Assembly replacement.

Remove Handwheel Assembly (LY 2001)

14. Remove the Handwheel Clutch (piece #16), Compression Spring (piece #17), Clutch Sleeve (piece #13),

Thrust Washer (piece #26 [2 pcs]), and Thrust Bearing (piece #27).

15. Remove four Screws (piece #70) and four Lockwashers (piece #71) from the Handwheel Cap Plate

(piece #69).

16. Remove the Handwheel Assembly as one piece (pieces #146, 41, 112, 69, 192, 134, and 37).

17. Go to Step 19.

Remove Handwheel Assembly (LY 3001)

14. Remove the Handwheel Clutch (piece #16), Compression Spring (piece #17), Clutch Sleeve (piece #13) and

Thrust Washer (piece #26 [2 pcs]), and Thrust Bearing (piece #27).

15. Remove Screws (pieces #63 and 65) and Lockwashers (piece #64 and 66) from the Spur Gear Cover

(piece #34) of the Handwheel Assembly.

16. Remove the Handwheel Assembly as one piece (pieces #146, 41, 112, 136, 39 [2 pcs], 34, 137, 116, 115, 38,

and 36).

17. Remove the Handwheel Pinion and Idler (piece #43) and Idler Shaft (piece #42).

18. Remove the Handwheel Gear Assembly (pieces #119, 35, and 37).

Remove Drive Sleeve

19. Remove the Roll Pins (piece #174) located in the end of the Mechanical Stop Screws (piece #58).

20. Remove the Mechanical Stop Screws (piece #58), Locking Nut (piece #59), Thread-Seal (piece #60), and

Retaining Washer (piece #184).

21. Remove O-Ring (piece #129) and Bearing (piece #33) from the top of the Drive Sleeve (piece #10).

22. Remove the Drive Sleeve (piece #10).

Remove Declutch Assembly

23. Remove Roll Pin (piece #121) and remove Declutch Lever (piece #45).

24. Push the Declutch Assembly (pieces #46, 48, 123, 122, and 44) up through the Housing and remove. Then

remove Declutch Return Spring (piece #47).

25. Remove O-Ring (piece #138) from the Housing.

Remove Input Worm Gear

26. Remove the Retaining Drive Ring (piece #113).

27. Remove Input Worm Gear (piece #18) and Lug Adapter (piece #25) as an assembly from the Ball Bearing

(piece #24).

Flow Control Division

Limitorque Actuation Systems

Summary of Contents for LY 1001 Series
































































Search results

Summary of Contents for LY 1001 Series

Reviews:

Related manuals for LY 1001 Series

Brands by name

Popular brands

Limitorque LY 1001 Series, Installation And Maintenance Manual

Search results

Summary of Contents for LY 1001 Series

Reviews:

Related manuals for LY 1001 Series

Brands by name

Popular brands