Lightware 91540021 Page 8 User Manual Download

Page: 8 / 119

1. Introduction

HDMI-TPS-RX110AY series – User's Manual

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

1.1.

Description

A small size HDBaseT

TPSreceiverunitisbeingdevelopedintheLightwareworkswithonePoEcapable

TPSinputandasingleHDMIoutput.Theunitisfull4K/UHDand3DcapableandHDCPcompliant.TheHDMI

audio is de-embedded to the balanced audio output via a Phoenix (Euroblock) connector, the audio port has

volume and balance control. The built-in Event Manager feature and the dual Relay module of the device are

bothconfigurableviatheLightwareDeviceControllersoftware.Furthercontroloptionsareservedbythe

USB, RS-232, IR (in and out), and Ethernet ports.

Model Denomination

1.2.

Compatible Devices

ThereceiveriscompatiblewithotherLightwareTPStransmitters,matrixTPSandTPS2boards,25GTPS2

boards, as well as third-party HDBaseT-extenders, displays, but not compatible with the phased out TPS-90

extenders.

ATTENTION!

The receiver is PoE-compatible (Power over Ethernet, can be powered remotely via using

CATx cable) but the device can only receive power and cannot send power other PoE-compatible devices.

Only the TPS connector is PoE-compatible, Ethernet port cannot receive power.

The receiver is compatible with any third-party HDBaseT

device.

HDBaseT

and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

HDMI-TPS-RX110AY-Plus

1x input and

1x output

HDBaseT

TPS extender

HDMI output interface Receiver

Audio

de-embedding

function

Advanced Control

Features

Built-in relays

The List of Compatible Lightware Devices

▪

MXModularmatrixframes-MX-TPS/TPS2-OB

▪

25G Modular matrix frames - 25G-TPS2-OB

▪

Standalone TPS matrix frames – MMX6x2-HT series

▪

TPStransmitters:

–

HDMI-TPS-TX95/96/97

–

WP/FP-HDMI-TPS-TX97

–

DVI-HDCP-TPS-TX95/96/97

–

UMX-TPS-TX100 series

–

WP/FP-UMX-TPS-TX100series

–

SW4-TPS-TX240

–

HDMI-TPS-TX200 series

–

DVI-HDCP-TPS-TX200series

–

DP-TPS-TX200 series

▪

Single port standalone TPS power injector – TPS-PI-1P1

1.3.

Box Contents

HDMI-TPS-RX110AY

series receiver

12VDCadaptorwith

interchangeable plugs

Phoenix

Combicon

3-pole connector

Phoenix

Combicon

4-poleconnector

Phoenix

Combicon

5-pole connector

Infrared detector unit

Infrared emitter unit

Safety and

Warranty

Info

Quick

Start

Guide

Safety&WarrantyInfo,

QuickStartGuide



 



Summary of Contents for 91540021
























































































































Search results

Summary of Contents for 91540021

Reviews:

Related manuals for 91540021

Brands by name

Popular brands

Lightware 91540021, User Manual

Search results

Summary of Contents for 91540021

Reviews:

Related manuals for 91540021

Brands by name

Popular brands