manualshive.com logo in svg

Lightware 91540021, User Manual

Share
Download
Lightware 91540021 User Manual Download Page 73

 

7.LW3Programmers’Reference

 

HDMI-TPS-RX110AY series – User's Manual 

73

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

7.5.12. 

HDCP Setting (Output Port)

HDCP capability can be set to Auto/Always on the output ports, thus, non-encrypted content can be

transmitted to a non-HDCP compliant display. See more information in the 

HDCP Management

 section.

Command and Response 

#hdcp

 

Î

SET·/MEDIA/VIDEO/

<out>

.HdcpModeSetting=

<HDCP_mode>

 

Í

pw·/MEDIA/VIDEO/

<out>

.HdcpModeSetting=

<HDCP_mode>

Parameters

Identifier

Parameter description

Value

Parameter value

<HDCP_mode>

HDCP mode

0

Auto

1

Always

Example

 

Î

SET/MEDIA/VIDEO/O1.HdcpModeSetting=0

 

Í

pw/MEDIA/VIDEO/O1.HdcpModeSetting=0

7.5.13. 

Test Pattern Generator Mode

The output port can send a special image towards the sink device for testing purposes. The setting is 

available on the input ports with the below-listed parameters.

Command and Response 

#testpattern

 

Î

SET·/MEDIA/VIDEO/

<out>

.TpgMode=

<mode>

 

Í

pw·/MEDIA/VIDEO/

<out>

.TpgMode=

<mode>

Parameters

Identifier

Parameter description

Value

Parameter value

<mode>

Test pattern generator 

mode

0

Always off

: the test pattern is not displayed on

the output.

1

Always on

: the test pattern is displayed on the

output.

2

Auto

:thetestpatternisdisplayedifthereisno

signal on the input port.

 Example

 

Î

SET/MEDIA/VIDEO/O1.TpgMode=2

 

Í

pw/MEDIA/VIDEO/O1.TpgMode=2

7.5.14. 

Test Pattern Generator Clock Source

Command and Response

 

Î

SET·/MEDIA/VIDEO/

<out>

.TpgClockSource=

<clock_frequency>

 

Í

pw·/MEDIA/VIDEO/

<out>

.TpgClockSource=

<clock_frequency>

Parameters

Identifier

Parameter description

Value

Parameter value

<clock_frequency>

Clock frequency

480

480p

576

576p

EXT

External clock (from actual TMDS source)

Example

 

Î

SET/MEDIA/VIDEO/O1.TpgClockSource=576

 

Í

pw/MEDIA/VIDEO/O1.TpgClockSource=576

7.5.15. 

Test Pattern Setting

Command and Response

 

Î

SET·/MEDIA/VIDEO/

<out>

.TpgPattern=

<pattern>

 

Í

pw·/MEDIA/VIDEO/

<out>

.TpgPattern=

<pattern>

Parameters

Identifier

Parameter description

Value

Parameter value

<pattern>

The test pattern displayed 

on the sink device

RED

Red

GREEN

Green

BLUE

Blue

BLACK

Black

WHITE

White

RAMP

Ramp

CHESS

Chess

BAR

Bar

CYCLE

Cycle setting means all the patterns are 

changed sequentially approx. in every 2 

seconds

Example

 

Î

SET/MEDIA/VIDEO/O1.TpgPattern=GREEN

 

Í

pw/MEDIA/VIDEO/O1.TpgPattern=GREEN

 

Summary of Contents for 91540021
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands