Lightware 91540021 Page 100 User Manual Download

Page: 100 / 119

8. Firmware Upgrade

HDMI-TPS-RX110AY series – User's Manual

100

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

Step 4.

Start the update and wait until it is finished.

Click on the

Start Update

button to start the procedure. The status is shown in percent in the right side of the

device line and the status of the all procedures in the lower light green progress bar.

Firmware upgrade is in progress

INFO:

Thedevicemightrebootseveraltimesduringthefirmwareupgradeprocedure.

Step 5.

Wait until the unit reboots with the new firmware.

Oncethefirmwareupgradeprocedureiscompleted,theunitrebootwiththenewfirmware.

Firmware upgrade procedure is done

8.5. Keeping the Configuration Settings

Bydefault,deviceconfigurationsettingsarerestoredwhenfirmwareupgradeisfinished.Iffactoryresethas

been chosen in the parameters window, all device settings will be erased. In the case of factory reset you

cansavethesettingsofthedeviceintheLightwareDeviceControllersoftwareandrestoreitlater.Seethe

details in the

ConfigurationCloning(BackupTab)

section.

Thefollowingflowchartdemonstrateshowthisfunctionworksinthebackground.

Start of the Upgrade

Thedevicerebootsandstartsinbootloadmode(firmwareupgrademode).

Backup

Thecurrentconfigurationofthedeviceisbeingsavedintoaconfigurationbackupfileonyour

computer.Youcanfindadetailedlistaboutthesavedsettingsinthe

Content of Backup File

section.

Upgrade

TheCPUfirmwareandtheFPGAbinaryarechangedtotheneweronesinthepackage.

Factory reset

Beforetheupgradeallconfigurationsettingsarerestoredtothefactorydefaultvalues.

Conversion / Restore

Beforetherestoreprocedurethefirmwarepackagechecksthebackupdataandifitisneeded,

aconversionisappliedtoavoidincompatibilityproblemsbetweenthefirmwareversions.

Aftertheconversionallconfigurationsettingsarerestoredtothedevice.

When the factory default option is enabled in the Parameters window, the conversion / restore procedure

will not be performed!

End

Oncethefirmwareupgradeprocedureisfinished,thedevicerebootsandisreadytouse.

Thedetailsabouttheprocedure:whenfirmwareupgradestarts,thefirststepismakingabackupofthe

settings of the device.The firmware package checks the backup data and if it is needed, a conversion

is applied to avoid incompatibility problems between the firmware versions. If you do not want to keep

configurationsettings,youcansetthe

Factory default

option enabled.



 



Summary of Contents for 91540021
























































































































Search results

Summary of Contents for 91540021

Reviews:

Related manuals for 91540021

Brands by name

Popular brands

Lightware 91540021, User Manual

Search results

Summary of Contents for 91540021

Reviews:

Related manuals for 91540021

Brands by name

Popular brands