Lightware 91540021 User Manual Download Page 85

Page: 85 / 119

7.LW3Programmers’Reference

HDMI-TPS-RX110AY series – User's Manual

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

7.11.2.

Change Command Injection Port Number

Command and Response

SET·/MEDIA/IR/

<in

out>

.CommandInjectionPort=

<port_no>

/MEDIA/IR/

<in

out>

.CommandInjectionPort=

<port_no>

Example

SET/MEDIA/IR/S1.CommandInjectionPort=9001

pw/MEDIA/IR/S1.CommandInjectionPort=9001

7.11.3. Enable/Disable Output Signal Modulation

Command and Response

SET·/MEDIA/IR/

<out>

.EnableModulation=

<logical_value>

pw·/MEDIA/IR/

<out>

.EnableModulation=

<logical_value>

Parameters

Identifier

Parameter description

Value

Explanation

<logical_value>

Signalmodulationenable/

disable setting

true

The signal modulation is enabled.

false

The signal modulation is disabled.

Example

SET/MEDIA/IR/D1.EnableModulation=false

pw/MEDIA/IR/D1.EnableModulation=false

Signal modulation is turned off on IR output (D1).

INFO:

The default setting value is

true

(enabled).

7.12.

Sending Message via the Communication Ports

7.12.1.

Sending a TCP Message (ASCII-format) via TCP Port

The command is for sending a command message in ASCII-format. This method allows escaping the control

characters. For more information see the

Escaping

section.

Command and Response

#message

CALL·/MEDIA/ETHERNET:tcpMessage(

<IP_address>

<port_no>

)

mO·/MEDIA/ETHERNET:tcpMessage

Example

CALL/MEDIA/ETHERNET:tcpMessage(192.168.0.103:6107=C00)

mO/MEDIA/ETHERNET:tcpMessage

The'C00'messageissenttotheindicatedIP:portaddress.

Example with HEX codes

CALL/MEDIA/ETHERNET:tcpMessage(192.168.0.20:5555=C00\x0a\x0d)

mO/MEDIA/ETHERNET:tcpMessage

The'C00'messagewithCrLf(CarriagereturnandLinefeed)issenttotheindicatedIP:portaddress.The

\xsequenceindicatestheHEXAcode;seemoreinformationinthe

Using Hexadecimal Codes

section.

7.12.2.

Sending a TCP Text (ASCII-format) via TCP Port

The command is for sending a text message in ASCII-format. This method

does not allow

sending message

with control and non-printable characters.

Command and Response

CALL·/MEDIA/ETHERNET:tcpText(

<IP_address>

<port_no>

<text>

)

mO·/MEDIA/ETHERNET:tcpText

Example

CALL/MEDIA/ETHERNET:tcpText(192.168.0.103:6107=pwr_on)

mO/MEDIA/ETHERNET:tcpText

Explanation

The'pwr_on'textissenttotheindicatedIP:portaddress.



 



Summary of Contents for 91540021
























































































































Search results

Summary of Contents for 91540021

Reviews:

Brands by name

Popular brands

Lightware 91540021, User Manual

Search results

Summary of Contents for 91540021

Reviews:

Brands by name

Popular brands