LightPointe AireLink 60 Installation And User Manual Download Page 72 | Manualshive

Page: 72 / 133

background image

AireLink



60 Installation and User Manual Rev. D

System Installation

Page 72

5.12

A

IRELINK™ 60 WITH 2 F

OOT ANTENNA

1.

The sight clamp for the Alignment Sight Tool is on the top (bottom) of the 2 foot antenna.

2.

Slide the Sight onto the mounting bracket as shown in Fig. 5-12 (right). It is very important to
make sure that the ridge on the bracket is engaged with the groove on the sight clamp.

Figure 5-12: Attach Alignment Sight Tool to external 2 foot antenna

5.13

CONFIGURATION OF THE ALIGNMENT SIGHT TOOL

The alignment sight clamp may need to be reconfigured for proper fit. Fig. 5-13 shows how to change
the configurations. To re-configure, remove the brass knob, move to clamp the desired position and
replace the knob.

Figure 5-13: Re-configuring Alignment Sight Tool

«
...
70
71
72
73
74
...
»

Summary of Contents for AireLink 60






































































































































Reviews:

No comments

Related manuals for AireLink 60

microTALK PR330C

Brand: Cobra Pages: 9

Brand: ConcealFab Pages: 22

Brand: EGG Pages: 52

Brand: Ubiquiti Pages: 36

Brand: Dataradio Pages: 35

Brand: Radio Shack Pages: 12

Brand: switel Pages: 52

Brand: KYL Pages: 6

Brand: SAM Electronics Pages: 84

Brand: Wood and Douglas Pages: 37

Brand: Midland Pages: 4

Brand: Sylvania Pages: 11

Brand: Uniden Pages: 32

Brand: Sanyo Pages: 8

Brand: Sanyo Pages: 35

Brand: JBL Pages: 4

Brand: OK. Pages: 93

Brand: Rockwell Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands