Lightmed TruScan 532 Operator'S Manual Download Page 84

Page: 84 / 115

TruScan 532 Single - Wavelength – Operators Manual Rev. No 02

Page 83 of 114

Fit the headpiece onto your head and adjust the two knobs to align the
Interpupillary distance

Verify illumination intensity integrity by adjusting the LCD LIO illumination
control knob (refer to fig. 5.16c)

Figure 5.16 (c) LCD LIO Intensity Control

Figure 5.16 (d) LIO Control Knob

Verify the spot size or zoom system is accordingly (from smallest to largest
size)

Ensure the different light aperture setting is also functioned accordingly
(refer to fig. 5.16d)

Ensure aiming spot light is able to tilt in up/down position (refer to fig. 5.16d)

Light Aperture
Setting Control

Aiming spot
light up/down

LIO Intensity
Control

Summary of Contents for TruScan 532




















































































































Search results

Summary of Contents for TruScan 532

Reviews:

Related manuals for TruScan 532

Brands by name

Popular brands

Lightmed TruScan 532, Operator'S Manual

Search results

Summary of Contents for TruScan 532

Reviews:

Related manuals for TruScan 532

Brands by name

Popular brands