Lightmed TruScan 532 Operator'S Manual Download Page 24

Page: 24 / 115

TruScan 532 Single - Wavelength – Operators Manual Rev. No 02

Page 23 of 114

Safety Filter

Fixed filter OD 4 @ 532nm

Beam
Divergence

Cone angle of 20°

Pattern Types Single, Line, Square (2x2, 3x3, 4x4, 5x5), Macular Arc (double, triple),

Circle (full, 1/4, 1/2, 3/4) and Triangle – Spot width, density and 360
rotation available for each pattern

Laser Indirect Ophthalmoscope (LIO)

Indirect model Keeler All Pupil II

Retinal Spot
size

300µm nominal at focus with 20D Laser Lens

Illumination
power

From Laser Console. Internal PSU allows intensity adjustment.
Connector is on Console Front Panel

Fiber length

3 m

Weight

Less than 500gms without laser attachment

Safety Filter

Fixed filter OD 4

Beam
Divergence

Cone angle 20c

Endo-ocular Probes

Probe Types

Straight, Curved and Aspirating

Fiber Length

3 m

Safety Filters

OD 4 in housing for installation to Operating Microscope before
Laser can be fired

Sterile

Sterilized by Ethylene Oxide and packed as Single use devices ready
for use

Beam
Divergence

0.2 NA

Safety filter

Safety Filters OD 4 @ 532nm

Summary of Contents for TruScan 532




















































































































Search results

Summary of Contents for TruScan 532

Reviews:

Related manuals for TruScan 532

Brands by name

Popular brands

Lightmed TruScan 532, Operator'S Manual

Search results

Summary of Contents for TruScan 532

Reviews:

Related manuals for TruScan 532

Brands by name

Popular brands