Lightmed TruScan 532 Operator'S Manual Download Page 110

Page: 110 / 115

TruScan 532 Single - Wavelength – Operators Manual Rev. No 02

Page 109 of 114

Err 501 - Shutter
Failure

-Shutter failed to open or
close

-Reboot the system

-If the problem persisted, call the
authorized service or manufacturer
for further assistance

Err 502 - Laser
Diode Current Too
High

-Laser diode current is
out of range or over the
limits

-Call the authorized service or
manufacturer for further assistance

Err 503 - Aiming
Laser Failure

-Aiming laser beam failure
or the laser intensity is >
1mW

-Call the authorized service or
manufacturer for further assistance

Err 5041 - Laser
Diode Temperature
Out of Tol/-
2.5C

-Ambient temp. is too high
or low which causes the
laser laser temp. TEC unable
to reach the stable or
preset value within 5 mins.

-Reboot the system

-If the problem persisted, call the
authorized service or manufacturer
for further assistance

Err 5042 - Laser
Sensor Failure

-Laser sensor failure
(opened or shorted
sensor)

-Power off ; call the authorized
service or manufacturer for further
assistance

Err 5043 - Cavity
Temperature Out of
Tol/- 2.5C

-Cavity Temperature
sensor can not reach to
the /- 2.5C

-Reboot the system

-If the problem persisted, call the
authorized service or manufacturer
for further assistance

Err 5044 - Cavity
Temperature
Sensor Failure

-Cavity temp. sensor

failure or the sensor is
open or shorted circuit

-Call the authorized service or
manufacturer for further assistance

Err 5051 - Remote
Communication
Error

-No communication
between remote and the
laser console within the
time of frame of 300ms

-Reboot the system

-If the problem persisted, call the
authorized service or manufacturer
for further assistance

Err 5052 - Remote
Time Up Error

-Timer in remote stopped
running for 1ms

-Reboot the system

-If the problem persisted, call the
authorized service or manufacturer
for further assistance

Err 5053 - Remote
ROM Error

-mismatched code in the
remote software when

-Reboot the system

-If the problem persisted, call the

Summary of Contents for TruScan 532




















































































































Search results

Summary of Contents for TruScan 532

Reviews:

Related manuals for TruScan 532

Brands by name

Popular brands

Lightmed TruScan 532, Operator'S Manual

Search results

Summary of Contents for TruScan 532

Reviews:

Related manuals for TruScan 532

Brands by name

Popular brands