Licht-Technik Motoryoke BigBee MB-D1 Functional Description Download Page 32

Page: 32 / 52

P12 TILT-down (negative) moving range

At this point the

TILT-down moving range

can be set. For the TILT-axis the moving

ranges (up and down) must be programmed individually. The negative moving range is
defined as the „direction bottom“ range. The moving ranges have the 0-position as
reference point. This point can be set in

P06, TILT-axis 0-position, page 30

Before programming this point read chapter TILT

-axis moving range, page 22

and

P06,

TILT-axis 0-position, page 30

Range of values:

10..182 degrees

Recommended value:

90°

Operation:

depress You are now on menu level. The last adjusted menu
point is displayed, e.g.:

Menu P01: DMX address motoryoke

depress ... until

Menu P12

is displayed

depress The second line displays the currently adjusted value.

depress Adjust the desired moving range

depress You are back on menu level.

depress The equipment is ready for operation.

Caution

Check the entire

moving range

of the lamp:

The lamp-manufacturer specify

minimum distances

to inflammable materials. Never fall

below the minimum distance in no position of the lamp!

Check that the

motoryoke

will not be lit when lamp is on top position.

Make sure that no cable will be

broken

bended

stretched

damaged

anyhow by

reason of turning the motoryoke!

Headlights generally must

not

be operated with the ignition electronic on the top. Observe

the specifications of the lamp manufacturer!

Motoryoke MB D1 V4.56 Rev 1.06

Menü

Summary of Contents for Motoryoke BigBee MB-D1





















































Search results

Summary of Contents for Motoryoke BigBee MB-D1

Reviews:

Related manuals for Motoryoke BigBee MB-D1

Brands by name

Popular brands

Licht-Technik Motoryoke BigBee MB-D1, Functional Description

Search results

Summary of Contents for Motoryoke BigBee MB-D1

Reviews:

Related manuals for Motoryoke BigBee MB-D1

Brands by name

Popular brands