LG ARUM072BTE5 Installation Manual Download Page 166

Page: 166 / 184

166

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Table 79: Error Codes, continued.

For detailed information on how to troubleshoot each error, see the Multi V Service Manual on www.lghvac.com.

ERROR CODE TABLES

Please refer to the Safety Precautions on pages 4-7 for more detail to prevent injury or death regarding the operation and service

troubleshooting of the Multi V product.

WARNING

Error Code

Description

Details

Outdoor Unit

1 1 3 1 Master outdoor unit liquid pipe temperature sensor

error.

• Check the connection on the outdoor unit PCB.
• Thermistor disconnected or shorted.

1 1 3 2 Slave1 outdoor unit liquid pipe temperature sensor

error.

1 1 3 3 Slave2 outdoor unit liquid pipe temperature sensor

error.

1 1 4 1 Master outdoor unit subcooling inlet temperature

sensor error.

• Check the connection on the outdoor unit PCB.
• Thermistor disconnected or shorted.

1 1 4 2 Slave1 outdoor unit subcooling inlet temperature

sensor error.

1 1 4 2 Slave2 outdoor unit subcooling inlet temperature

sensor error.

1 1 5 1 Master outdoor unit subcooling outlet temperature

sensor error.

• Check the connection on the outdoor unit PCB.
• Thermistor disconnected or shorted.

1 1 5 2 Slave1 outdoor unit subcooling outlet temperature

sensor error.

1 1 5 3 Slave2 outdoor unit subcooling outlet temperature

sensor error.

1 1 6 1 Master outdoor unit low oil level or oil level sensor

error.

• Master outdoor unit may have low oil levels.
• Master outdoor unit oil level sensor disconnected or shorted.

1 1 6 2 Slave1 outdoor unit oil level sensor error.

• Slave1 outdoor unit may have low oil levels.
• Slave1 outdoor unit oil level sensor disconnected or shorted.

1 1 6 3 Slave2 outdoor unit oil level sensor error.

• Slave2 outdoor unit may have low oil levels.
• Slave2 outdoor unit oil level sensor disconnected or shorted.

1 4 5 1 Communication error between master outdoor unit

main board and external board.

Master outdoor unit main board to external board communica-

tion failure.

1 4 5 2 Communication error between slave1 outdoor unit

main board and external board.

Slave1 outdoor unit main board to external board communica-

tion failure.

1 4 5 3 Communication error between slave2 outdoor unit

main board and external board.

Slave2 outdoor unit main board to external board communica-

tion failure.

1 5 0 1 Master outdoor unit compressor discharge superheat

not satisfied.

• Outdoor unit compressor discharge superheat not satisfied for

≥5 minutes.

• Code can only occur when the outdoor is operating in cooling

mode (all indoor units must be in cooling mode; error cannot

occur during simultaneous operation).

• After at least 10 minutes of compressor operation, the master

outdoor unit microprocessor will calculate the system’s com-

pressor superheat. If at any time during compressor operation

where all indoor units in thermal on are in cooling mode and

the compressor superheat falls <3ºC for ≥5 minutes, there is

a high probability that liquid could flood back to the inlet of the

compressor scroll, resulting in compressor damage.

• If error occurs 3 times within any 1 hour period of compressor

operation, the system will shut down and remain off. A manual

restart will be necessary.

1 5 0 2 Slave1 outdoor unit compressor discharge superheat

not satisfied.

1 5 0 3 Slave2 outdoor unit compressor discharge superheat

not satisfied.

1 5 1 1 Master outdoor unit operation mode conversion error.

Pressure imbalance between outdoor units.

1 5 1 2 Slave1 outdoor unit operation mode conversion error.

1 5 1 3 Slave2 outdoor unit operation mode conversion error.

Summary of Contents for ARUM072BTE5

























































































































































































Search results

Summary of Contents for ARUM072BTE5

Reviews:

Related manuals for ARUM072BTE5

Brands by name

Popular brands

LG ARUM072BTE5, Installation Manual

Search results

Summary of Contents for ARUM072BTE5

Reviews:

Related manuals for ARUM072BTE5

Brands by name

Popular brands