LG ARUM072BTE5 Installation Manual Download Page 78

Page: 78 / 184

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Model

PRHR022A

PRHR032A

PRHR042A

Number of Ports

Connecting Pipes

To Indoor Units

Liquid Pipe (inches)

3/8

Vapor Pipe (inches)

5/8

To Outdoor Units

Liquid (inches)

3/8

1/2

5/8

Low-pressure Vapor (inches)

7/8

1-1/8

High-pressure Vapor (inches)

3/4

7/8

INSTALLING FOR HEAT RECOVERY

OPERATION

Heat Recovery Units

1. Series connection of heat recovery units: Total

capacity of indoor units ≤192,000 Btu/h.

2. Refer to the heat recovery unit PCB for valve group

control setting.

3. Maximum capacity of each port is 54,000 Btu/h and

eight (8) indoor units.

Do not skip ports when connecting indoor

units. Start at port 1, then use 2, then use 3, then

use 4 (the numbers are displayed on the heat

recovery ports).

Vapor Pipe Ø5/8, Liquid Pipe Ø3/8

Brazed Connections

1 2

3 4

Remove Caps Before

Brazing

Liquid Pipe

Low Pressure Vapor Pipe
High Pressure Vapor Pipe

Close Up of the Heat Recovery Unit Connections.

Heat Recovery Unit Connections and Limitations

Table 37: Heat Recovery Unit Piping Connection Sizes.

Removing the Caps

Before brazing the field-supplied refrigerant piping to the heat recovery unit connections, the caps MUST be removed from the liquid, high

pressure vapor, and low pressure vapor pipe connections.

Removing the caps releases any gas present in the heat recovery unit. If the gas isn’t released, physical injury or death may occur from the uncon-

trolled rapid release of gas, or if the gas comes in contact with a flare during brazing and generates a poisonous gas.

Piping Connection Options

Heat recovery units can connect to the field-supplied refrigerant piping on the left side or on the right side. Heat recovery units can also be

installed in series / in parallel using these side connections.

Pipe Connection from Left Side

Series / Parallel Pipe Connection

Pipe Connection from Right Side

Heat Recovery Unit Piping Connection Options.

On whichever port or pipe not used, the factory-provided cap must be removed, and that port / pipe must be recapped and insulated.

Summary of Contents for ARUM072BTE5

























































































































































































Search results

Summary of Contents for ARUM072BTE5

Reviews:

Related manuals for ARUM072BTE5

Brands by name

Popular brands

LG ARUM072BTE5, Installation Manual

Search results

Summary of Contents for ARUM072BTE5

Reviews:

Related manuals for ARUM072BTE5

Brands by name

Popular brands