LG ARUM072BTE5 Installation Manual Download Page 56 | Manualshive

Page: 56 / 184

background image

56

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

Outdoor Unit Y-Branches

Outdoor unit Y-branches can only be installed in a horizontal or vertical UP configuration.

The vertical DOWN configuration is not permitted.

When installed vertically, position the Y-branch at a level lower than the outdoor units it serves, so the straight-through leg is within ±3° of

plumb. When installed horizontally, the straight-through leg should be level, and the branch leg should be within ±5° of horizontal rotation.
Outdoor unit Y-branches must always be installed with the two port ends connected to the piping coming from the outdoor units, and the sin-

gle port end towards the indoor unit refrigerant piping system supporting the indoor units. Outdoor unit Y-branches are usually installed close

to the outdoor unit, leaving enough space for servicing and maintenance.

Indoor Unit Y-Branch Horizontal Configuration.

Indoor Unit Y-branch Vertical Installation Alignment

Specifications.

+5°

Horizontal

Plane

-5°

Branch Leg

Straight-through Leg

ELEVATION VIEW

Y-branch Inlet

-3° of Plumb +3° of Plumb

-3° of Plumb +3° of Plumb

Vertical DOWN Configuration for

Outdoor Unit Y-Branches

NOT PERMITTED

.

Vertical UP Configuration for Indoor Unit

Y-Branches.

Outdoor Unit Y-Branch Kits

INSTALLING FOR HEAT PUMP

OPERATION

Diagram of an Incorrect Outdoor Unit Y-branch Installation.

To Next Branch

To Indoor Units

Y-Branch Insulation and Piping Detail.

LG-Supplied

Insulation Jacket

Field-Supplied

Insulation

Field-Supplied

Insulation

Field-Supplied Copper Piping

LG Supplied

Y-Branch

PLAN VIEW

No Substitutions on Piping Components

Only LG supplied Y-branch and Header fittings can be used to join one pipe segment to two or more segments.

Third-party

or field-fabricated components such as tee’s, Y-fittings, couplings, headers, or other branch fittings are not permitted. The

only field-provided fittings allowed in a Multi V piping system are 45° and 90° long radius elbows and full port ball valves (if

applicable).

ELEVATION VIEW

«
...
54
55
56
57
58
...
»

Summary of Contents for ARUM072BTE5

























































































































































































Reviews:

No comments

Related manuals for ARUM072BTE5

Brand: TCF Pages: 19

Brand: Haier Pages: 56

Brand: Daikin Pages: 20

Brand: Jafanda Pages: 6

DELUXE HIGH WALL MINI SPLIT

Brand: ICP Pages: 26

Brand: Haier Pages: 8

Brand: Haier Pages: 25

Brand: Haier Pages: 30

Brand: Haier Pages: 8

Brand: Haier Pages: 16

Brand: Haier Pages: 17

HSU-18HEA03(T3)

Brand: Haier Pages: 8

Brand: Haier Pages: 27

Brand: Haier Pages: 4

Brand: Haier Pages: 18

Brand: Haier Pages: 16

HSU-09HVD03/R2 - annexe 2

Brand: Haier Pages: 14

Brand: Haier Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands