LG ARUM072BTE5 Installation Manual Download Page 125

Page: 125 / 184

125

Pre-Commissioning

Due to our policy of continuous product innovation, some specifications may change without notification.

Setting the Optional Modes

Static Pressure Compensation

Function (Fn2)

Static Pressure Compensation function modifies the maximum out-

door unit fan speed during normal system operation. Use to raise the

maximum outdoor unit fan speed to compensate for an obstruction

(duct) in airflow.
The default outdoor fan external static pressure rating for Multi V 5

Outdoor Units is 0.16 in-wg. Selecting “op3” raises the fan speed to

produce the same airflow at 0.32 in-wg.
Refer to the Multi V Engineering Manuals for the default static

pressure rating, and the maximum static pressure rating with this

function engaged.
For use on both heat pump and heat recovery systems.

Table 47: Setting Static Pressure Compensation Function.

Turn No. 5 on the master outdoor unit PCB

DIP switch bank SW01 to ON.

Select the “Func” mode by using the SW03C forward ►button and the

SW02C backward ◄ button, and then press the SW01C confirm

● button.

Select the “Fn2” function by using the SW03C forward ►button and

the SW02C backward ◄ button, and then press the SW01C

confirm ● button.

Select from “oFF”, “op1” through “op3” options (see table) by using the

SW03C forward ►button and the SW02C backward ◄ button,

and then press the SW01C confirm ● button.

Press the SW01D Reset Button one (1) time to reset PCB.

The selected option value is saved in the EPROM.

Setting the Static Pressure Compensation Function.

• Ask a trained LG service provider to set this function during system

installation.

• If the outdoor unit RPM is changed, cooling capacity may be

reduced.

Settings

Nominal 6 Ton (RPM)

ESP (in-wg)

Nominal 8 to 20 Ton (RPM)

ESP (in-wg)

oFF (Default)

880

0.16

1,000

0.16

op1

910

0.231

1,040

0.25*

op2

930

0.271

1,070

0.27*

op3

950

0.32

1,100

0.32

*Settings “op1” and “op2” are interpolated externals static pressure values given the values for “oFF” and “op3”.

PRE-COMMISSIONING

Summary of Contents for ARUM072BTE5

























































































































































































Search results

Summary of Contents for ARUM072BTE5

Reviews:

Related manuals for ARUM072BTE5

Brands by name

Popular brands

LG ARUM072BTE5, Installation Manual

Search results

Summary of Contents for ARUM072BTE5

Reviews:

Related manuals for ARUM072BTE5

Brands by name

Popular brands