LG ARUM072BTE5 Installation Manual Download Page 110

Page: 110 / 184

110

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Between Multiple Indoor Units

Operating as a Group (Group

Control)

If any indoor units were specified to operate in unison:

• Before running cable, decide which indoor unit will be the “Mas-

ter.” The other indoor units in that group will be designated as

“Slave(s).” The zone controller will be connected to the “Master.”

• Set the pertinent DIP switch at each indoor unit to identify the

Master and Slave(s). On wall mounted indoor unit models, set the

assignment using the handheld remote controller.

• Use a daisy chain configuration and connect all of the group’s

indoor units together starting at the “Master” unit.

•

NEVER splice, cut, or extend cable length with field provided

cable. Always include enough cable to cover distance between all

components.

For indoor units with hardwired connections SIG - 12V -

GND (Comm.) terminals:

• From the controller to the master indoor unit, use 22 AWG,

3-conductor, twisted, stranded, unshielded. All wiring must comply

with all applicable local and national codes.

• From the master indoor unit to the slave indoor unit(s), daisy chain

using 22 AWG, 3-conductor, twisted, stranded, unshielded

(

Do not attach wire to 12VDC terminal to the slave indoor

units). All wiring must comply with all applicable local and national

codes.

For indoor units with CN-REMO connections:

Use Group Control Kit (sold separately) containing extension and

Y-splitter cables. Use one (1) group control cable kit for each indoor

unit in the group except for the last indoor unit.

ELECTRICAL

Communication Cable Specifications

• Cable connected to zone controller is the factory default connection.

• Indoor unit connections depend on indoor unit type.

CN-REMO

Supplied

LG Supplied Group Control Kit (PZCWRCG3)

Master Indoor Unit

Indoor Unit

Example of Indoor Unit Group to Zone Controller

Connections (Sig-12V-GND [Comm.] Terminal).

Example of Indoor Unit Group to Zone Controller

Connections (CN-REMO).

Master Indoor Unit

Indoor Unit

Signal

12VDC Comm.

Signal

12VDC Comm.

Signal

12VDC Comm.

Signal

12VDC Comm.

Summary of Contents for ARUM072BTE5

























































































































































































Search results

Summary of Contents for ARUM072BTE5

Reviews:

Related manuals for ARUM072BTE5

Brands by name

Popular brands

LG ARUM072BTE5, Installation Manual

Search results

Summary of Contents for ARUM072BTE5

Reviews:

Related manuals for ARUM072BTE5

Brands by name

Popular brands