LG ARUM072BTE5 Installation Manual Download Page 159

Page: 159 / 184

159

Error Codes

Due to our policy of continuous product innovation, some specifications may change without notification.

Error Code

Description

Details

Indoor Unit

0 1

- Indoor unit return air or optional remote wall tempera-

ture sensor communications error.

Indoor unit air temperature sensor disconnected or shorted.

(Check the wiring, connection on the indoor unit PCB, then check

the thermistor.)

0 2

- Indoor unit inlet pipe temperature sensor communica-

tion error.

Indoor unit inlet pipe temperature sensor is disconnected or

shorted. (Check the connection on the indoor unit PCB, then

check the thermistor.)

0 3

- Communication error between zone controller and

indoor unit.

Indoor unit PCB is not receiving communications signal from

zone controller.

0 4

- Indoor unit drain pump error.

Drain pump and/or flow switch is/are malfunctioning. Also check

drain line for obstructions.

0 5

• Communication error between indoor unit communi-

cation PCB and indoor unit.

• Communication error between outdoor unit and

indoor unit.

• Indoor unit PCB is not receiving signal from indoor unit communi-

cations PCB for >3 consecutive minutes. Check PCBs for issues.

• Indoor unit PCB is not receiving communications signal from

outdoor unit. Check indoor unit to outdoor unit communication

cable connections for issues.

0 6

- Indoor unit or hydro kit outlet pipe temperature sensor

error.

• Indoor unit outlet pipe temperature sensor is disconnected or

shorted. (Check the connection on the indoor unit PCB, then

check the thermistor.)

• Hydro kit liquid side temperature sensor is disconnected or

shorted. Values read less than -43°C or greater than +96°C

(less than -45.4°F or greater than +204.8°F).

0 7

- Indoor units are not operating in the same mode. (Heat

pump applications only)

Different operation mode between indoor units.

0 8

- Hydro kit hot water storage tank temperature

sensor error.

Pipe temperature sensor disconnected or shorted.

0 9

- Indoor unit EPROM error.

• Communication error between the indoor unit PCB board and its

option card. (The option card is about 1′ x 1′ and is plugged into

the indoor unit PCB board. Check connection between the two.)

• Communication error between EPROM on indoor unit main PCB.

• Indoor unit EPROM data is not available.

Table 72: Error Codes.

For detailed information on how to troubleshoot each error, see the Multi V Service Manual on www.lghvac.com.

Please refer to the Safety Precautions on pages 4-7 for more detail to prevent injury or death regarding the operation and service

troubleshooting of the Multi V product.

WARNING

ERROR CODE TABLES

Error Code Display

The seven segment display on the main board displays error codes.

Error codes are 3 or 4 digit numbers. The rightmost number desig-

nates the ODU frame (1=Master; 2=Slave1; 3=Slave2). The other

two or three digits indicate the error.
Examples: 211 = Error No. 21 on master unit; 212 = Error No. 21 on

slave 1 unit; 213 = Error No. 21 on slave2 unit, 1051 = Error No. 105

on master unit.

• If two or more errors occur simultaneously, the lower error code

number is displayed first.

• After error is resolved, the error code disappears.

Nomenclature Definitions

• MICOM: Non-volatile memory chip where unit setup information is stored.

•

EPROM: Non-volatile memory chip where device identification, size, and factory defined default component operating parameters are stored.

The error code tables below and on the following pages list the error codes used for Multi V systems. For detailed information on how to

troubleshoot each error, see the Multi V 5 Service Manual on www.lghvac.com.

2 1 2

c 1 2

Repeats

Compressor Error

Unit; 1 = Master, 2 = Slave1, 3 = Slave2

Example of an Error Code.

Summary of Contents for ARUM072BTE5

























































































































































































Search results

Summary of Contents for ARUM072BTE5

Reviews:

Related manuals for ARUM072BTE5

Brands by name

Popular brands

LG ARUM072BTE5, Installation Manual

Search results

Summary of Contents for ARUM072BTE5

Reviews:

Related manuals for ARUM072BTE5

Brands by name

Popular brands