LES Applications
Note:
This setting is for touch-screen models only.
This menu setting is used to enable or disable Lexmark Embedded Solutions (LES) applications. This setting
does not affect built
‑
in applications.
To change the settings, perform the following steps:
1
From the Configuration menu, navigate to
LES applications
.
2
Press the left or right arrow to navigate, then select
Enable
or
Disable
.
3
Touch
Submit
.
Press
Back
to return to the Configuration menu.
Key Repeat Initial Delay
Note:
This setting is available only on the MS610de model.
This setting determines the length of delay before a repeating key starts repeating. The range is 0.25–5
seconds, with increments of 0.25. The default setting is one second.
To adjust this setting:
1
From the Configuration menu, navigate to
Key Repeat Initial Delay
.
2
Touch the arrow keys to adjust the setting.
3
Touch
to save the setting, or press
X
to return to the Configuration menu without saving any changes.
Key Repeat Rate
Note:
This setting is available for touch screen models only.
This setting indicates the number of presses per second for repeating keys. The range is 0.5–30, with
increments of 1.
To adjust this setting:
1
From the Configuration Menu, navigate to
Key Repeat Rate
.
2
Touch the arrow keys to adjust the setting.
3
Touch
to save the setting, or press
X
to return to the Configuration Menu without saving any changes.
Clear Supply Usage History
This setting reverts the supply usage history (number of pages and days remaining) to the factory shipped level.
To clear the supply usage history:
1
From the Configuration menu, navigate to
Clear Supply Usage History
.
2
Depending on the printer model, press
OK
or touch
Clear Supply Usage History
to proceed.
7015
Service menus
250
Summary of Contents for XM1135
