Error code
Description
Action
80A
T5 Timeout occurred when transmitting
image data to remote fax device.
•
Check line quality.
•
Adjust ‘Transmit Level’.
•
Select a lower ‘Max Speed’ value
under Fax Send settings.
80B
Too many errors when transmitting in ECM
mode.
•
Check line quality.
•
Adjust ‘Transmit Level’.
•
Select a lower ‘Max Speed’ value
under Fax Send settings.
80C
Remote device failed to respond to the
CTC command.
•
Select a lower ‘Max Speed’ value
under Fax Send settings.
•
Adjust ‘Transmit Level’.
80D
Received too many requests from remote
end to repeat the previous command sent.
•
Check line quality.
•
Adjust ‘Transmit Level’.
•
Check if line conditions on remote
end will facilitate a good connection.
80E
Functional limitation-Remote fax device
does not support G3 receive capability.
No action needed. Issue with the remote
device.
811
Failed to detect a fax device at the remote
end.
•
Verify MFD is answering to fax call
and not a voice call.
•
Decrease value of ‘Rings To Answer’
setting.
812
No more data rates available in V34
modulation scheme.
Adjust to a lower modulation scheme.
813
Timeout occurred after waiting too long to
receive a good frame.
Adjust “Receive Threshold”.
814
Tried too many times at selected speed
using V34 modulation scheme.
•
Adjust ‘Transmit Level’.
•
Adjust to a lower modulation
scheme.
815
Fax transmission was interrupted due to
power failure.
Troubleshoot MFP if error persists. See
“Modem/fax card service check” on
page 189
818
Fax transmission failed due to insufficient
memory to store scanned image.
Adjust ‘Memory Use’ setting to allocate
more memory for send jobs.
819
Fax transmission failed due to insufficient
memory to store received image.
Adjust ‘Memory Use’ setting to allocate
more memory for receive jobs.
81A
A timeout occurred during transmission of
a page in ECM mode.
Select a lower ‘Max Speed’ value under
Fax Send settings.
880
Failure to transmit training successfully in
V17, V29, V27 terminal modulation
schemes.
•
Select a lower “Max Speed” under
Fax Send settings.
•
Adjust the “Transmit Level”.
•
Check line quality.
7015
Diagnostics and troubleshooting
196
Summary of Contents for XM1135
