Lexmark X95x Service Manual Download

Page: 725 / 1153

Repair information

4-251

7558-

xxx

Go Back

Position the ADF feed roller in its uppermost position to allow access to the ADF sensors, as shown in the
following image.

10.

Move the brackets out from under the ADF feed roller.

11.

Release the hooks securing the sensor (ADF scan width 1) (C).

12.

Remove sensor (ADF scan width 1).

Sensor (ADF scan width 2) removal

Open the ADF top door.

Remove the ADF front cover. See

“ADF front cover removal” on page 4-210

Summary of Contents for X95x


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands

Lexmark X95x, Service Manual

Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands