Lexmark X95x Service Manual Download

Page: 245 / 1153

Diagnostic information

2-195

7558-

xxx

Go Back

381.32 Sensor (booklet end guide HP) lag jam

Check the booklet front tamper

motor for proper operation.

When performing

motor tests, ensure

that all cover and

door interlock

switches are

overridden.

1. Enter the Diagnostics Menu.
2. Touch

MOTOR TESTS

3. Touch

FINISHER MOTOR

TESTS

4. Touch

Booklet tamper front

motor (reverse)

5. Touch

Booklet tamper front

motor (reverse)

Does the above component
operate properly?

Go to step 6.

Go to step 5.

Is the booklet front tamper
motor properly connected?

Replace the booklet front tamper

motor. Go to

“Booklet front

tamper motor removal” on
page 4-324

Replace the connection.

Perform a POR.

Does the error continue when
the power is turned off/on?

Replace the booklet controller

card assembly. Go to

“Booklet

controller card assembly
removal” on page 4-319

Problem resolved

Perform a POR.

Does the error continue when
the power is turned off/on?

Replace the finisher controller

PCBA. Go to

“Finisher PCBA

removal” on page 4-350

Problem resolved

Step

Action and questions

Yes

Check the booklet unit interface

connector assembly.

Is the above component free of
damage?

Go to step 2.

Replace the booklet unit interface

contact.

Check the main connector on the

booklet unit sensor interface

cable assembly.

Is the above component free of
damage?

Go to step 3.

Replace the booklet sensor

interface cable assembly.

Check the main connector on the

booklet unit motor interface cable

assembly.

Is the above component free of
damage?

Go to step 4.

Replace the booklet motor

interface cable assembly.

Step

Action and questions

Yes

Summary of Contents for X95x


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands

Lexmark X95x, Service Manual

Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands