Lexmark X95x Service Manual Download

Page: 194 / 1153

2-144

Service Manual

7558-

xxx

Go Back

Check the sensor (ADF

registration) for proper

connection.

Is the above component
properly connected?

Replace the sensor (ADF

registration). Go to

“Sensor

(ADF registration) removal” on
page 4-244

Replace the connections.

Check the sensor (ADF inverter)

for proper operation.

1. Enter the Diagnostics Menu.
2. Touch

SENSOR TESTS.

3. Touch

ADF/SCANNER

SENSOR TESTS

4. Touch

Sensor (ADF

inverter).

Does the display on the
operator panel change every
time the sensing area of the
above sensor is interrupted or
blocked?

Go to step 7.

Go to step 6.

Check the sensor (ADF inverter)

for proper connection.

Is the above component
properly connected?

Replace the sensor (ADF

inverter). Go to

“Sensor (ADF

inverter) removal” on
page 4-241

Replace connections.

Check the ADF feed motor for

proper operation.

When performing

motor tests, ensure

that all cover and

door interlock

switches are

overridden.

1. Enter the Diagnostics Menu.
2. Touch

MOTOR TESTS

3. Touch

ADF/SCANNER

MOTOR TESTS

4. Touch

ADF registration

motor

Does the above component
operate properly?

Go to step 9.

Go to step 8.

Check the ADF registration motor

for proper connection.

Is the above component
properly connected?

Replace the ADF registration

motor. Go to

“ADF registration

motor removal” on page 4-215

Replace the connections.

Place an undamaged document

in the ADF, and perform an ADF

test.

Does the error remain?

Replace the ADF controller

PCBA. Go to

“ADF controller

PCBA removal” on page 4-200

Problem resolved

Step

Action and questions

Yes

Summary of Contents for X95x


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands

Lexmark X95x, Service Manual

Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands