Lexmark X95x Service Manual Download

Page: 324 / 1153

2-274

Service Manual

7558-

xxx

Go Back

Spots

Check the LED printhead assembly for proper

installation.
Install the LED printhead assembly properly, and

perform a print test.

Does the problem remain?

Go to step 8.

Problem

resolved

Check the LED printhead assembly.
Replace the LED printhead assembly.
Go to

“LED printhead removal” on page 4-102

Does the problem remain?

Go to step 9.

Problem

resolved

Check the upper printer engine PCBA for proper

connectivity. Disconnect and reconnect all appropriate

cables.
Replace the upper printer engine PCBA.
Go to

“Upper printer engine PCBA removal” on

page 4-186

Perform a print test.

Does the problem remain?

Problem solved.

Replace the RIP

card PCBA.
Go to

“RIP

PCBA removal”
on page 4-150

Step

Check

Yes

Check the media condition.
Load new, dry, recommended media.
Reprint the defective image.

Does the problem remain?

Go to step 2.

Problem

resolved

Check the media transfer route.

Is the media route free of contamination or debris?

Go to step 3.

Remove debris

contamination.

Step

Check

Yes

Leading edge

Trailing edge

Summary of Contents for X95x


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands

Lexmark X95x, Service Manual

Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands