Lexmark X95x Service Manual Download

Page: 700 / 1153

4-226

Service Manual

7558-

xxx

Go Back

Remove the four screws (D) securing the FB CCD sensor assembly to the machine.

Disconnect the CCD ribbon cable from the FB CCD sensor assembly.

Warning:

When disconnecting the CCD ribbon cable from the FB CCD sensor assembly, make sure that the

release hook is pressed or the connection will be damaged.

Summary of Contents for X95x


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands

Lexmark X95x, Service Manual

Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands