Lexmark X95x Service Manual Download

Page: 290 / 1153

2-240

Service Manual

7558-

xxx

Go Back

842.02 Scanner communication failure

842.03 Scanner communication failure

Perform a POR.

Does the error remain when the
power is turned off/on?

Replace the scanner controller

PCBA.
Go to

“Scanner controller

PCBA removal” on page 4-235

Go to step 4.

Problem resolved

Perform a POR.

Does the error remain when the
power is turned off/on again?

Replace the RIP PCBA.
Go to

“RIP PCBA removal” on

page 4-150

Problem resolved

Step

Action and questions

Yes

Check the scanner interface

cable assembly connection

between the RIP card assembly

and the scanner unit assembly.

Is the scanner interface cable
assembly connected properly?

Go to step 2.

Replace the connection.

Check all connections of the

scanner controller PCBA.

Are the connections of the
scanner controller card
assembly connected properly?

Go to step 3.

Connect each connector of the

scanner controller card assembly

properly.

Perform a POR.

Does the error remain when the
power is turned off/on?

Replace the scanner controller

PCBA.
Go to

“Scanner controller

PCBA removal” on page 4-235

Go to step 4.

Problem resolved

Perform a POR.

Does the error remain when the
power is turned off/on again?

Replace the RIP PCBA.
Go to

“RIP PCBA removal” on

page 4-150

Problem resolved

Step

Action and questions

Yes

Check the scanner interface

cable assembly connection

between the RIP card assembly

and the scanner unit assembly.

Is the scanner interface cable
assembly connected properly?

Go to step 2.

Replace the connection.

Step

Action and questions

Yes

Summary of Contents for X95x


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands

Lexmark X95x, Service Manual

Search results

Summary of Contents for X95x

Reviews:

Related manuals for X95x

Brands by name

Popular brands