Lexmark X95x Service Manual Download Page 228

Page: 228 / 1153

2-178

Service Manual

7558-

xxx

Go Back

381.12 Stacker bin failure

Check the media eject clamp

clutch for proper operation.

When performing

motor tests, ensure

that all cover and

door interlock

switches are

overridden.

1. Enter the Diagnostics Menu.
2. Touch

MOTOR TESTS

3. Touch

FINISHER MOTOR

TESTS

4. Touch

Media eject clutch.

Does the above component
make an audible clicking
noise?

Go to step 7.

Go to step 6.

Check the media eject clamp

clutch for proper connection.

Is the above component
properly connected?

Replace the media eject clamp

clutch. Go to

“Media eject clamp

clutch removal” on page 4-365

Replace the connection.

Perform a POR.

Does the error continue when
the power is turned off/on?

Replace the finisher controller

PCBA. Go to

“Finisher PCBA

removal” on page 4-350

Problem resolved

Step

Action and questions

Yes

Check the vertical transport

mechanism of the stacker bin for

obstacles and damage.

Are the any obstacles in the
vertical transport mechanism
of the stacker bin?

Remove obstacles.

Go to step 2.

Check the sensor (stacker bin

level encoder) for proper

operation.

1. Enter the Diagnostics Menu.
2. Touch

SENSOR TESTS

3. Touch

FINISHER SENSOR

TESTS

4. Touch

Sensor

(stacker bin

level encoder)

Does the display on the
operator panel change every
time the sensing area of the
above sensor is interrupted or
blocked?

Go to step 4.

Go to step 3.

Step

Action and questions

Yes

Summary of Contents for X95x


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X95x

Reviews:

Lexmark X95x, Service Manual, Page: 228 / 1153

Search results

Summary of Contents for X95x

Reviews: