Lexmark X95x Service Manual Download Page 384

Page: 384 / 1153

3-48

Service Manual

7558-

xxx

Go Back

Paper jam in cover F (paper transport)

Open cover F.

Firmly grasp the jammed paper on each side, and then gently pull it out.

Note:

Make sure all paper fragments are removed.

Note:

If the paper jam is difficult to remove, then rotate the knob counterclockwise.

Close cover F.

If necessary, touch

Continue

from the printer control panel.

Summary of Contents for X95x


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X95x

Reviews:

Lexmark X95x, Service Manual, Page: 384 / 1153

Search results

Summary of Contents for X95x

Reviews: