Lenovo tihnkserver rd330 Hardware Maintenance Manual Download Page 48

Page: 48 / 198

Intelligent Diagnostics Module connector

Redundant power supply connector 2

Front VGA connector

Backplane power connector 1

SATA connector 0

Backplane power connector 2

SAS connector 4-7

System fan 7 connector

SAS connector 0-3

Microprocessor socket 2

System board battery

System fan 6 connector

Platform Controller Hub (PCH)

Memory slots (6)

Internal USB Type A connector 1

System fan 5 connector

TMM Premium connector

System fan 3 connector

Internal USB Type A connector 2

Microprocessor socket 1

TPM connector

System fan 2 connector

iButton socket

Memory slots (6)

ThinkServer Management Module

System fan 1 connector

Front panel connector

Used to connect the front panel cable.

Internal USB connector 1

Used to connect the front panel USB cable.

Internal USB connector 2

Reserved for the manufacturer.

Intelligent Diagnostics Module connector

Used to connect the cable of the Intelligent Diagnostics Module.

Front VGA connector

Used to connect the cable of the front VGA connector on the front panel of the server.

SATA connector 0

Used to connect the signal cable of the slim optical drive if the server has one installed.

SAS connector 4-7

Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the
hard disk drive 4 to hard disk drive 5.

SAS connector 0-3

Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the
hard disk drive 0 to hard disk drive 3.

ThinkServer RD330 Hardware Maintenance Manual

Summary of Contents for tihnkserver rd330







































































































































































































Search results

Summary of Contents for tihnkserver rd330

Reviews:

Brands by name

Popular brands

Lenovo tihnkserver rd330, Hardware Maintenance Manual

Search results

Summary of Contents for tihnkserver rd330

Reviews:

Brands by name

Popular brands