manualshive.com logo in svg

Lenovo tihnkserver rd330, Hardware Maintenance Manual

Share
Download
Lenovo tihnkserver rd330 Hardware Maintenance Manual Download Page 158

To replace the front panel board, do the following:

1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all

power cords from electrical outlets and disconnect all cables that are connected to the server.

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server.

3. Remove the server cover. See “Removing the server cover” on page 71.

4. Locate the front panel board. See “Front view of the server” on page 14.

5. Disconnect the front panel cable and the front panel USB cable from the rear of the front panel board.

6. Remove the two screws that secure the front panel board, and then carefully remove the front panel

board from the chassis.

ID

Mem

CPU

PSU

Figure 93. Removing the front panel board

7. Touch the static-protective package that contains the new front panel board to any unpainted surface

on the outside of the server. Then, take the new front panel board out of the package.

Note:

Carefully handle the front panel board by its edges.

144

ThinkServer RD330 Hardware Maintenance Manual

Summary of Contents for tihnkserver rd330







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands