manualshive.com logo in svg

Lenovo tihnkserver rd330, Hardware Maintenance Manual

Share
Download
Lenovo tihnkserver rd330 Hardware Maintenance Manual Download Page 43

ThinkServer RAID 700 Adapter (also known as ThinkServer 9260-8i SAS RAID Adapter)

The following illustration shows the connectors on the ThinkServer RAID 700 Adapter.

Figure 16. ThinkServer RAID 700 Adapter

1

Ports 7-4

3

ThinkServer RAID 700 Battery connector

2

Ports 3-0

1

Ports 7-4

Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 31.

2

Ports 3-0

Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 31.

3

ThinkServer RAID 700 Battery connector

Used to connect a ThinkServer RAID 700 Battery. See “Installing or removing the ThinkServer RAID 700
Battery” on page 95.

Hot-swap hard disk drive backplane

Your server comes with one of the following hot-swap hard disk drive bay and backplane configurations:

• Up to four 3.5-inch hot-swap SATA or SAS hard disk drives with one backplane

• Up to six 2.5-inch hot-swap SAS hard disk drives or SATA solid-state drives with one backplane

To locate the backplane, see “Server components” on page 23.

Backplane for 3.5-inch hard disk drives

This topic provides information to help you locate the connectors on the backplane for 3.5-inch hard disk
drives.

Chapter 3

.

Product overview

29

Summary of Contents for tihnkserver rd330







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands