manualshive.com logo in svg

Lenovo tihnkserver rd330, Hardware Maintenance Manual

Share
Download
Lenovo tihnkserver rd330 Hardware Maintenance Manual Download Page 173

4. Ensure that the cover latch is in the open position. Place the server cover above the chassis so that

the cover latch is aligned with the cover latch slot in the chassis. Then, lower the server cover onto
the chassis until the cover latch is inserted into its slot and both sides of the server cover engage the
guides on both sides of the chassis.

ID

CPU

Mem

PSU

Figure 109. Installing the server cover

5. Pivot the cover latch to the closed position and slide the server cover to the front of the chassis at the

same time until the server cover snaps into position and the cover latch is completely closed.

ID

CPU

Mem

PSU

Figure 110. Closing the server cover completely

6. If the server is installed in a rack cabinet, reinstall the server into the rack cabinet. See the

Rack

Installation Instructions

that comes with the server.

Chapter 6

.

Installing, removing, or replacing hardware

159

Summary of Contents for tihnkserver rd330







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands