manualshive.com logo in svg

Lenovo tihnkserver rd330, Hardware Maintenance Manual

Share
Download
Lenovo tihnkserver rd330 Hardware Maintenance Manual Download Page 160

1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all

power cords from electrical outlets and disconnect all cables that are connected to the server.

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server.

3. Remove the server cover. See “Removing the server cover” on page 71.

4. Remove the cooling shroud. See “Removing and reinstalling the cooling shroud” on page 75.

5. Locate the riser card assembly 1. See “Server components” on page 23.

6. Grasp the riser card assembly 1 by its edges and carefully lift it straight up and off the chassis.

Figure 95. Lifting the riser card assembly 1 off the chassis

7. If there is any PCI Express card (such as an Ethernet card) installed on the riser card assembly 1, note

down the cable connections, disconnect all cables from the card, and then completely remove the riser
card assembly 1 out of the chassis. Then, remove the PCI Express card from the riser card assembly 1.
See “Removing the Ethernet card” on page 85.

8. Touch the static-protective package that contains the new riser card assembly 1 to any unpainted

surface on the outside of the server. Then, take the new riser card assembly 1 out of the package.

146

ThinkServer RD330 Hardware Maintenance Manual

Summary of Contents for tihnkserver rd330







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands