manualshive.com logo in svg

Lenovo 30CY, Hardware Maintenance Manual, Page: 86 / 224

Share
Download
Lenovo 30CY Hardware Maintenance Manual Download Page 86

•  The computer voltage matches the voltage available at the electrical outlet for your country or region.

The operating system fails to start up.

Solution:

Ensure that the startup device sequence set in the Setup Utility program includes the device where the 
operating system resides. Usually, the operating system is on the internal storage drive. For more 
information, see “Changing the startup device sequence permanently” on page 70.

The computer beeps multiple times before the operating system starts up.

Solution:

Ensure that no keys are stuck.

Audio problems

The audio cannot be heard on the Windows operating system.

Solutions:

•  If you are using powered external speakers that have an On/Off control, ensure that:  

–  The On/Off control is set to the 

On 

position.

–  The speaker power cable is connected to a properly grounded, functional ac electrical outlet.

•  If your external speakers have a volume control, ensure that the volume is not set too low.

•  Click the volume icon in the Windows notification area on the taskbar. Ensure that the mute speakers 

settings are not selected and none of the volume settings is set too low.

Note:

If the volume icon is not displayed in the Windows notification area, add the icon to the notification 

area. See the Windows help system.

•  For some computers that have a front audio panel, ensure that the volume is not set too low.

•  Ensure that your external speakers (and headphones, if used) are connected to the correct audio 

connectors on the computer. Most speaker cables are color-coded to match the connectors.

Note:

When external-speaker or headphone cables are connected to the audio connectors, the internal 

speaker, if present, is disabled. In most cases, if an audio adapter is installed in one of the expansion 
slots, the audio function built into the system board is disabled. Therefore, you must use the audio 
connectors on the audio adapter.

•  Ensure that the program you are running is designed for use on the Windows operating system. If the 

program is designed to run in DOS, the program does not use the Windows sound feature. The program 
must be configured to use Sound Blaster Pro or Sound Blaster emulation.

•  Ensure that the audio device drivers are correctly installed.

The sound comes from one of the external speakers.

Solutions:

•  Ensure that the speaker cable is inserted completely into the connector on the computer.

•  Right-click the volume icon in the Windows notification area on the taskbar. Then, click 

Open Volume 

Mixer 

and select the desired speaker. Click the 

Levels 

tab and ensure that the Balance settings are set 

correctly. 

Note:

If the volume icon is not displayed in the Windows notification area, add the icon to the notification 

area. See the Windows help system.

78

P330 Hardware Maintenance Manual

Summary of Contents for 30CY

































































































































































































































Reviews:

No comments