manualshive.com logo in svg

Lenovo 30CY, Hardware Maintenance Manual, Page: 119 / 224

Share
Download
Lenovo 30CY Hardware Maintenance Manual Download Page 119

b.  Locate the hole in the plastic holder to install the retention latch. Align the pin 

a 

with the 

corresponding hole 

b 

in the plastic holder. Then press the retention latch downward into the hole 

until it snaps into position. 

Figure 38. Installing the retention latch

c.  Hold the new M.2 solid-state drive by its edges and ensure that the circuit board side is facing 

upward. Align the contact edge of the new drive with the key in the corresponding slot. Then carefully 
insert the new drive into the slot at an angle of about 20 degrees and pivot the new drive downward. 
Insert the plug of the retention latch into the hole to secure the new drive. 

Note:

Do not touch the circuit board of the M.2 solid-state drive.

Figure 39. Installing the M.2 solid-state drive

Chapter 9

.

Hardware removal and installation

111

Summary of Contents for 30CY

































































































































































































































Reviews:

No comments