Lenovo 30CY Hardware Maintenance Manual Download Page 149

Page: 149 / 224

• To complete the installation or replacement, go to “Completing the parts replacement” on page 187.

Type-1 storage-drive cage

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

Some computer models come with a type-1 storage-drive cage for installing or replacing a 3.5-inch storage
drive or a 2.5-inch storage drive.

3.5-inch storage drive

To remove or install a 3.5-inch storage drive in the type-1 storage-drive cage, do the following:

1. Prepare your computer. See “Preparing your computer” on page 98.

2. Locate the type-1 storage-drive cage. See “Computer components” on page 33.

3. To remove a 3.5-inch storage drive in the type-1 storage-drive cage, do the following:

a. Disconnect the signal cable and the power cable from the storage drive.

b. Remove the screw and slide the type-1 storage-drive cage downward to release it from the drive bay

assembly.

Figure 96. Removing the type-1 storage-drive cage

Chapter 9

Hardware removal and installation

141

Summary of Contents for 30CY

































































































































































































































Search results

Summary of Contents for 30CY

Reviews:

Lenovo 30CY, Hardware Maintenance Manual, Page: 149 / 224

Search results

Summary of Contents for 30CY

Reviews: