manualshive.com logo in svg

Lenovo 30CY, Hardware Maintenance Manual, Page: 81 / 224

Share
Download
Lenovo 30CY Hardware Maintenance Manual Download Page 81

–  Consists of at least two SATA storage drives

–  Supported strip size: 4 KB, 8 KB, 16 KB, 32 KB, 64 KB, or 128 KB

–  Better performance without fault tolerance

•  RAID 1: mirrored disk array 

–  Consists of two SATA storage drives

–  Improved reading performance and 100% redundancy

To install an additional storage drive, refer to “Type-1 storage-drive cage” on page 141.

Configuring the system BIOS to enable SATA RAID functionality

This section describes how to configure the system BIOS to enable SATA RAID functionality.

Note:

Use the arrow keys on the keyboard to make selections.

To enable SATA RAID functionality, do the following: 

1.  Start the Setup Utility program. See “Starting the Setup Utility program” on page 65.

2.  Select 

Devices 

➙ 

ATA Drive Setup 

and press Enter.

3.  Select 

Configure SATA as 

and press Enter.

4.  Select 

RAID 

and press Enter.

5.  Press F10 or Fn+F10 (depending on the keyboard) to save the new settings and exit the Setup Utility 

program.

Configuring RAID in UEFI mode

This section provides instructions on how to configure RAID in UEFI mode. 

Creating RAID volumes in UEFI mode

Attention:

All the existing data stored on the selected drives will be erased while the RAID volume is being 

created.

To create RAID volumes, do the following: 

1.  Start the Setup Utility program. See “Starting the Setup Utility program” on page 65.

2.  Select 

Devices 

➙ 

ATA Drive Setup 

and press Enter.

3.  Select 

Intel (R) Rapid Storage Technology 

and press Enter.

4.  Select 

Create RAID Volume 

and press Enter.

5.  Select 

Name 

and press Enter. When prompted, type a proper RAID Volume name in the field.

6.  Select 

RAID Level 

and press Enter. When prompted, select a RAID level in the field.

7.  Use the arrow keys and the space key to mark individual physical storage drives to be added in the RAID 

volume.

8.  Select 

Strip Size 

and press Enter. When prompted, select a strip size in the field.

9.  Select 

Capacity 

and type a volume size in the field.

10.  Select 

Create Volume 

and press Enter to initiate volume creation.

Deleting RAID volumes in UEFI mode

Attention:

All the existing data stored on the selected drives will be erased after you delete RAID volumes.

To delete RAID volumes, do the following: 

Chapter 6

.

Advanced configuration

73

Summary of Contents for 30CY

































































































































































































































Reviews:

No comments