manualshive.com logo in svg

Lenovo 30CY, Hardware Maintenance Manual, Page: 158 / 224

Share
Download
Lenovo 30CY Hardware Maintenance Manual Download Page 158

c.  Align the four holes in the rear of the type-2 storage-drive cage with the corresponding hooks in the 

drive bay assembly. Then slide the type-2 storage-drive cage upward until it snaps into position. 
Reinstall the screw to secure the type-2 storage-drive cage. 

Figure 113. Installing the type-2 storage-drive cage

d.  Connect the signal cable and the power cable to the new storage drive.

What to do next:

•  To work with another piece of hardware, go to the appropriate section.

•  To complete the installation or replacement, go to “Completing the parts replacement” on page 187.

Power button

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter 

1 “Read this first: Important safety information” on page 1. 

To remove or install the power button, do the following: 

1.  Prepare your computer. See “Preparing your computer” on page 98.

2.  Locate the power button. See “FRUs and CRUs” on page 35.

3.  Disconnect the power button cable from the front-bezel connector on the system board. See “Parts on 

the system board” on page 38.

150

P330 Hardware Maintenance Manual

Summary of Contents for 30CY

































































































































































































































Reviews:

No comments