manualshive.com logo in svg

Lenovo 30CY, Hardware Maintenance Manual, Page: 47 / 224

Share
Download
Lenovo 30CY Hardware Maintenance Manual Download Page 47

Figure 6. System board part locations

1 

4-pin microprocessor power connector

2 

Microprocessor

3 

Microprocessor fan connector

4 

Memory slots (DIMM)

5 

Front-bezel connector

6 

Internal-speaker connector

7 

Storage-drive activity indicator

8 

Flex bay fan connector

9 

10-pin system board power connector

10 

SATA power connectors

11 

Front-fan connector

12 

Clear CMOS/Recovery jumper

13 

SATA 3 connector

14 

SATA 4 connector or eSATA connector

15 

SATA 2 connector

16 

SATA 1 connector

17 

M.2 solid-state drive slot

18 

Wi-Fi card slot

19 

Thermal-sensor connector

20 

ThinkStation

® 

LED connector

21 

Front USB 2.0 connectors (available on some models)

22 

Parallel connector

23 

Serial port (COM) connector

24 

Thunderbolt

™ 

control connector

25 

PCIe x16 card slot (negotiable link width x4)

26 

PCIe x1 card slot

27 

PCIe x16 card slot

28 

Coin-cell battery

29 

Rear-fan connector 

30 

E-lock connector

31 

DisplayPort connector

32 

Cover presence switch connector (Intrusion switch 

connector)

33 

PS/2 keyboard and mouse connector

Chapter 2

.

Product overview

39

Summary of Contents for 30CY

































































































































































































































Reviews:

No comments