Lenovo 10AQ Maintenance Manual Download Page 58 | Manualshive

Page: 58 / 184

Lenovo 10AQ Maintenance Manual Download Page 58

Lenovo Solution Center

The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems. It
combines diagnostic tests, system information collection, security status, and support information, along
with hints and tips for maximum system performance.

Notes:

• The Lenovo Solution Center program can be downloaded from http://www.lenovo.com/diags.

• If you are using a Windows operating system other than Windows 7, Windows 8, or Windows 8.1, go to

http://www.lenovo.com/diags for the latest information on diagnostics for your computer.

To run the Lenovo Solution Center program, see “Lenovo programs” on page 30.

For additional information, refer to the Lenovo Solution Center help system.

Note:

If you are unable to isolate and repair the problem yourself after running the program, save and print

the log files. You will need the log files when you speak to a Lenovo technical support representative.

54

ThinkCentre E93 Hardware Maintenance Manual

«
...
56
57
58
59
60
...
»

Summary of Contents for 10AQ

























































































































































































Reviews:

No comments