manualshive.com logo in svg

Lenovo 10AQ, Maintenance Manual, Page: 114 / 184

Share
Download
Lenovo 10AQ Maintenance Manual Download Page 114

• If you are installing a memory module, open the retaining clips of the memory slot into which you

want to install the memory module.

Figure 40. Opening the retaining clips

7. Position the new memory module over the memory slot. Make sure that the notch

1

on the memory

module aligns correctly with the slot key

2

on the system board. Push the memory module straight

down into the slot until the retaining clips close.

Figure 41. Installing a memory module

8. Reinstall the PCI Express x16 graphics card if you have removed it.

9. Lower the drive bay assembly.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 122.

Replacing the system board

CAUTION:

The heat sink and microprocessor might be very hot. Turn off the computer and wait three to five
minutes to let the computer cool before removing the computer cover.

110

ThinkCentre E93 Hardware Maintenance Manual

Summary of Contents for 10AQ

























































































































































































Reviews:

No comments