Lenovo 10AQ Maintenance Manual Download Page 153

Page: 153 / 184

7. Align the new power supply assembly in the chassis and slide the new power supply assembly into

the rail until the new power supply assembly clicks into position.

8. Align the screw holes in the new power supply assembly with the corresponding holes in the rear of the

chassis. Then, install the three screws to secure the new power supply assembly in place.

Note:

Use only screws provided by Lenovo.

Figure 91. Installing the power supply assembly

9. Connect the new power supply assembly cables to all drives and the system board. See “Locating

parts on the system board” on page 80.

10. Lower and position the heat sink fan duct on the top of the heat sink and fan assembly until it snaps

into position.

Chapter 10

Replacing FRUs (machine type: 10AQ)

149

Summary of Contents for 10AQ

























































































































































































Search results

Summary of Contents for 10AQ

Reviews:

Lenovo 10AQ, Maintenance Manual, Page: 153 / 184

Search results

Summary of Contents for 10AQ

Reviews: