background image

Page 3

KHA180, 240

KHA180 & 240 Parts Arrangement 

INDOOR COIL

OUTDOOR

FANS

OUTDOOR

COIL

CONDENSATE

DRAIN

FILTERS

(SIX − 24 X 24 X 2")

ECONOMIZER

(OPTIONAL)

ELECTRIC HEAT

(OPTIONAL)

COMPRESSORS

BLOWERS

FILTER

DRIERS

Shipping and Packing List 

Package 1 of 1 contains:

1− Assembled unit

Check unit for shipping damage. Receiving party should
contact last carrier immediately if shipping damage is found.

General 

These instructions are intended as a general guide and
do not supersede local codes in any way. Authorities
having jurisdiction should be consulted before
installation.

Availability of units and options varies by brand.

Requirements 

The KHA unit is ETL certified for outdoor installations only
at the clearances to combustible materials listed on unit
nameplate and in figure 1.

Installation of KHA heat pumps must conform with
standards in National Fire Protection Association (NFPA)
Standard for Installation of Air Conditioning and
Ventilating Systems NFPA No. 90A," Standard for
Installation of Residence Type Warm Air Heating and Air
conditioning Systems NFPA No. 90B," local municipal
building codes and manufacturer’s installation
instructions.

The National Electric Code (ANSI/NFPA No. 70−1984) is
available from:

National Fire Protection Association
470 Atlantic Avenue
Boston, MA 02210

UNIT CLEARANCES

C

D

B

A

Outdoor

Air Hood

FIGURE 1

1Unit

Clearance

A

in.(mm)

B

in.(mm)

C

in.(mm)

D

in.(mm)

Top

Clearance

Service

Clearance

45

(1143)

36

(914)

36

(914)

66

(1676)

Unob-

structed

Minimum Opera-

tion Clearance

45

(1143)

36

(914)

36

(914)

41

(1041)

Unob-

structed

Note − Entire perimeter of unit base requires support when elevated above
mounting surface.

   1

Service Clearance 

− Required for removal of serviceable parts.

Minimum Operation Clearance 

− Required clearance for proper unit operation.

Summary of Contents for KHA180

















Reviews: