background image

Page 5

BLOWER DATA

G40UH−36A−045 PERFORMANCE

External Static

Air Volume / Watts at Various Blower Speeds

External Static

Pressure

High

Medium−High

Medium−Low

Low

in. w.g.

cfm

Watts

cfm

Watts

cfm

Watts

cfm

Watts

0.00

1480

615

1300

545

1100

460

930

385

0.05

1465

605

1290

530

1100

450

930

380

0.10

1445

585

1280

520

1100

445

930

370

0.15

1440

585

1275

505

1095

435

935

365

0.20

1415

570

1260

495

1090

425

935

360

0.25

1400

560

1250

485

1090

420

930

355

0.30

1375

545

1235

470

1075

410

930

350

0.40

1320

520

1195

450

1060

390

915

330

0.50

1265

495

1160

430

1020

375

890

320

0.60

1210

475

1105

410

975

350

840

295

0.70

1135

450

1045

380

910

325

775

280

0.80

1025

415

915

345

810

300

720

265

0.90

885

380

815

320

725

270

640

240

NOTE − All air data is measured external to unit with 1 in. cleanable filter (not furnished − field provided) in place. Also see Filter Air Resistance table.

G40UH−36A−070 PERFORMANCE

External Static

Air Volume / Watts at Various Blower Speeds

External Static

Pressure

High

Medium−High

Medium−Low

Low

in. w.g.

Pa

cfm

L/s

Watts

cfm

L/s

Watts

cfm

L/s

Watts

cfm

L/s

Watts

0.00

0

1500

710

705

1290

610

565

985

465

455

830

390

375

0.05

12

1475

695

695

1275

600

555

980

465

445

820

385

365

0.10

25

1450

685

680

1255

590

545

970

460

440

810

380

360

0.15

37

1425

675

670

1240

585

535

965

455

430

805

380

355

0.20

50

1400

660

655

1225

580

525

955

450

425

795

375

350

0.25

62

1370

645

645

1205

570

510

945

445

415

790

375

345

0.30

75

1340

630

630

1180

555

500

930

440

405

780

370

335

0.40

100

1285

605

610

1140

540

475

900

425

390

745

350

325

0.50

125

1215

575

580

1080

510

450

865

410

375

705

335

310

0.60

150

1150

545

560

1015

480

430

810

380

355

655

310

290

0.70

175

1060

500

535

940

445

405

730

345

330

585

275

270

0.80

200

955

450

515

800

375

370

655

310

305

480

225

260

0.90

225

785

370

475

605

285

325

585

275

270

410

195

255

NOTE − All air data is measured external to unit with 1 in. (25 mm) cleanable filter (not furnished − field provided) in place. Also see Filter Air Resistance table.

G40UH−36B−090 PERFORMANCE

External Static

Air Volume / Watts at Various Blower Speeds

External Static

Pressure

High

Medium−High

Medium−Low

Low

in. w.g.

Pa

cfm

L/s

Watts

cfm

L/s

Watts

cfm

L/s

Watts

cfm

L/s

Watts

0.00

0

1500

710

720

1255

590

595

1040

490

460

900

425

370

0.05

12

1485

700

705

1250

590

580

1040

490

450

895

420

365

0.10

25

1465

690

685

1240

585

570

1035

490

445

890

420

360

0.15

37

1450

685

675

1235

585

555

1035

490

440

885

420

355

0.20

50

1435

675

660

1225

580

545

1030

485

435

880

415

350

0.25

62

1420

670

645

1215

575

530

1025

485

425

875

415

345

0.30

75

1400

660

630

1200

565

520

1020

480

415

870

410

340

0.40

100

1345

635

595

1170

550

495

1000

470

400

855

405

330

0.50

125

1300

615

575

1135

535

475

965

455

380

830

390

300

0.60

150

1235

585

545

1080

510

445

930

440

360

780

370

290

0.70

175

1165

550

510

1020

480

415

870

410

340

740

350

280

0.80

200

1080

510

480

940

445

385

800

380

315

670

315

260

0.90

225

985

465

445

840

395

355

710

335

290

600

285

245

NOTE − All air data is measured external to unit with 1 in. (25 mm) cleanable filter (not furnished − field provided) in place. Also see Filter Air Resistance table.

Summary of Contents for G40UHX Series















































Reviews: