background image

Page 9

BLOWER DATA

G40UH−60C−110 with 1 hp motor PERFORMANCE − Bottom Return Air, Side Return Air with Optional RAB Return Air
Base, Return Air from Both Sides or Return Air from Bottom and One Side.

External Static

Air Volume / Watts at Different Blower Speeds

External Static

Pressure

High

Medium−High

Medium−Low

Low

in. w.g.

Pa

cfm

L/s

Watts

cfm

L/s

Watts

cfm

L/s

Watts

cfm

L/s

Watts

.00

0

2655

1250

1407

2370

1120

1063

2085

985

894

1665

785

679

.10

25

2580

1215

1376

2350

1110

1043

2065

975

875

1650

780

667

.20

50

2500

1180

1346

2305

1085

1012

2045

965

849

1645

775

662

.30

75

2410

1135

1305

2230

1050

978

2010

950

820

1640

775

649

.40

100

2320

1095

1270

2165

1020

947

1940

915

786

1625

765

634

.50

125

2225

1050

1235

2090

985

914

1895

895

763

1610

760

622

.60

150

2130

1005

1205

2000

945

880

1840

870

740

1570

740

603

.70

175

2030

955

1155

1915

905

851

1760

830

709

1535

725

590

.80

200

1925

910

1123

1820

860

823

1670

790

681

1475

695

566

.90

225

1795

845

1078

1690

795

788

1560

735

655

1395

660

537

NOTE − All air data is measured external to unit with 1 in. (25 mm) cleanable filter (not furnished − field provided) in place. Also see Filter Air Resistance table.

G40UH−60C−110 with 1 hp motor PERFORMANCE − Single Side Return Air − Air volumes in bold require field fabricated
transition to accommodate 20 x 25 x 1 in. (508 x 635 x 25 mm) cleanable air filter in order to maintain proper air velocity.

External Static

Air Volume / Watts at Different Blower Speeds

External Static

Pressure

High

Medium−High

Medium−Low

Low

in. w.g.

Pa

cfm

L/s

Watts

cfm

L/s

Watts

cfm

L/s

Watts

cfm

L/s

Watts

.00

0

2430

1145

1309

2245

1060

1006

1910

900

843

1635

770

686

.10

25

2355

1110

1277

2190

1035

978

1905

900

817

1620

765

677

.20

50

2280

1075

1242

2140

1010

950

1885

890

797

1610

760

667

.30

75

2205

1040

1218

2075

980

924

1860

875

782

1605

755

655

.40

100

2130

1005

1189

2005

945

905

1815

855

752

1595

750

636

.50

125

2045

965

1159

1920

905

864

1750

825

726

1565

740

619

.60

150

1955

920

1132

1850

875

840

1700

800

705

1525

720

605

.70

175

1860

875

1105

1760

830

817

1610

760

674

1475

700

582

.80

200

1755

830

1067

1670

790

789

1540

725

654

1395

660

560

.90

225

1645

775

1033

1575

745

763

1445

680

627

1325

625

540

NOTE − All air data is measured external to unit with 1 in. (25 mm) cleanable filter (not furnished − field provided) in place. Also see Filter Air Resistance table.

Summary of Contents for G40UHX Series















































Reviews: