LENCO RC-8-2 Manual Download Page 6

11.  To program other equipment, repeats the Steps 1-9 for your VCR, SAT, AUD 
and or your second TV or VCR or SAT.  

Press the [SET] key to for 2 seconds 
Press & release the [CH+] 
Press the [SET] key once 
Press the [DEVICE] key to select a desired mode 
Press the [SET] key to save the working code   

P.5 
SETTING UP BY LEARNING 
The RC-8-2 comes with a complete library of pre-programmed codes. After you 
have set up the RC-8-2 for your device, you may find that there are one or more 
keys that you had on the original remote control, which do not have a place on 
the RC-8-2 keypad. 
The RC-8-2 offers a special learning feature that allows you to copy almost any 
function from your original remote control onto the keypad of the RC-8-2. Except 
to the Macro keys, [SET] key and Device mode keys. 
Before you start : 
?Make sure your original remote control is working correctly. 
?Make sure neither your RC-8-2, nor your original remote control is pointing at 
your device. 
To Learning (direct) : 
For example: To copy the "PIP" function from your original TV remote control 
onto the "I

I" key of your RC-8-2. 

1.  Place the RC-8-2 and your original remote control on a flat surface. Make 
sure the ends which you normally point at your device are facing each other. 
Point the original remote to the front center head of the RC-8-2 (see picture 
below). Keep the remotes at a distance of 2 to 5 cm. 
2.  Press the [SET] key to for 2 seconds and the LCD will be shown CODE 
SETUP.  
3.  Press & release the [CH+] key for two (2) times to view the LEARN MODE 
page. 
4.  Upon the LCD shown as LEARN MODE, press the [SET] key once. The LCD 
now shown TV IR LEARN. Press the [Device] key to select a desired mode (TV, 
VCR, SAT or AUD, etc..). In this case is [TV] key. 
5.  Press the [SET] key once and the RC-8-2 LCD shown as TV LEARN KEY.  
6.  Press the "I

I" key on the RC-8-2 remote where you want to place the 

learned function, the LCD shown as TV LEARNING. 
7.  Press & hold the key that you want to copy (Example: PIP key on your 
original remote control). 
8.  After learning is OK, the LCD shown as SUCEESS for 3 seconds then 
shown as TV LEARN KEY. If you want to copy other functions within the same 
mode, simply repeat steps 6 and 7 pressing the next key you want to copy by 
learning.  

Summary of Contents for RC-8-2














Reviews: