LENCO RC-8-2 Manual Download Page 3

The RC-8-2 provides you to view the current status of Weekday and Clock. 
Simply follow below steps: 
1.  Press the [SET] key to for 2 seconds and the LCD will be shown CODE 
SETUP.  
2.  Press & release the [CH+] for three (3) times to view the CLOCK SET page. 
3.  Upon the LCD shown as CLOCK SET, press the [SET] key once. 
4.  The HOUR of LCD will be blinks, press the [CH+] or [CH-] key to select 
desired HOUR.  
5.  Press the [SET] key once, the MINUTE of LCD will be blinks, press the [CH+] 
or [CH-] key to select desired MINUTE. 
6.  Press the [SET] key once, the WEEKDAY of LCD will be blinks, press the 
[CH+] or [CH-] key to select desired WEEKDAY. 
7.  Check the setting of Weekday and Clock, if it is OK then press the [SET] key 
to confirm and LCD shown as SUCCESS. 
NOTE : 
?Press the [SET] key to confirm and store the setting of weekday and clock. 
?During the set up of HOUR or MINUTE or WEEKDAY, you can leave the set up 
individually by pressing of the [ESC] key to escape and the LCD shown as EXIT 
and back to normal operation mode. 
?Press the [ESC] key for escape and the selected setting will not be stored.   

Press the [SET] key to for 2 seconds  
Press & release the [CH+] for three (3) times 
Press the [SET] key to confirm 
Press the [CH+/-] key to select desired  
Hour / Minute / Weekday   

P.3 
SETTING UP BY DIRECT CODE 
Example: To set up the RC-8-2 for your TV: 
1.  Make sure your TV is switched on (not on standby). 
2.  Press the [SET] key for 2 seconds and the LCD will be shown CODE 
SETUP. 
3.  Press & release the [SET] key and the LCD will be shown TV-001 page. 
4.  Press the [Device] key to select a desired mode (TV, VCR, SAT or AUD, etc.). 
In this case is [TV] key. 
5.  Enter the 3-Digit TV code from the code list for your brand equipment.   

If you perform this procedure correctly, the LCD shown the code 

number and then SUCCESS   

If not, the LCD shown as ERROR mean that the code number may 

not correct. 
6.  Aim the RC-8-2 at your TV and press the [POWER] key. Your TV should turn 
off.   If none of the keys or only some of the keys operate your TV, please repeat 
Steps 1-5, trying each code listed for your brand until you find the one that 
operates your TV. 

Summary of Contents for RC-8-2














Reviews: