manualshive.com logo in svg

LEGRAND vaddio 999-99800-100, Complete Manual, Page: 83 / 95

Share
Download
LEGRAND vaddio 999-99800-100 Complete Manual Download Page 83

Operation, Storage, and Care

For smears or smudges on the product, wipe with a clean, soft cloth. Use a lens cleaner on the lens. Do not
use any abrasive chemicals.

Keep this device away from food and liquids.

Do not operate or store the device under any of the following conditions:

n

Temperatures above 40°C (104°F) or below 0°C (32°F)

n

High humidity, condensing or wet environments

n

Inclement weather

n

Severe vibration

n

Going over Niagara Falls in a barrel

n

Dry environments with an excess of static discharge

Do not attempt to take this product apart. There are no user-serviceable components inside.

And a friendly reminder from our Training department...

As much as you might love our gear, do not attempt to romance your camera. As a robot it
cannot return your love.

78

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Summary of Contents for vaddio 999-99800-100
































































































Reviews:

No comments