manualshive.com logo in svg

LEGRAND vaddio 999-99800-100, Complete Manual, Page: 22 / 95

Share
Download
LEGRAND vaddio 999-99800-100 Complete Manual Download Page 22

System Administration

This chapter covers settings for managing the camera as an element of your network.

What controls do you need?

Go to this screen

Network settings

n

Hostname

n

DNS server

n

DHCP or static addressing

n

Static: IP address, subnet mask, gateway

Networking

Access management

n

Account passwords

n

Guest access

n

Idle session time-out

n

Telnet access enabled/disabled

n

Advanced security settings

Security

Time zone and NTP server (source for system time/date)

Networking

Information about the camera location

Help desk phone number for end users

Room Labels

See

Configuring Camera Behavior

for information on image adjustments, streaming configuration, and

other items related to camera behavior.

Note

Vaddio's cameras all have very similar web interfaces. Some of the screen shots in this manual may be
from other models.

17

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Summary of Contents for vaddio 999-99800-100
































































































Reviews:

No comments