LEGRAND DA-LITE Tensioned Advantage Series User Manual Download Page 7 | Manualshive

Page: 7 / 61

background image

7

CAUTION: Contact Da-Lite at 800-622-3737 or 574-267-8101 if door motor needs adjustment.

ATTENTION: Contactez Da-Lite au 800-622-3737 ou au 574-267-8101 au cas le moteur de porte
doit être ajusté.

NOTE: Use a screw driver or 5/32" Allen wrench to make adjustments.

More Screen Drop

1. Place operating switch in “down” position.

2. When the screen stops, turn the “down” limit knob

(Fig. 2) one-quarter turn counterclockwise. Test by
raising picture surface approximately two feet, then
lower again. Repeat until desired picture surface
position is attained.

CAUTION: Do not adjust for more drop than what

was ordered. At least 1–1/2 wraps of fabric must

remain on the roller. This screen comes standard

with 12" black

at the top.

ATTENTION! N'effectuez pas de réglage pour

obtenir un déroulement supérieur à celui
commandé. Au moins 1 à 1/2 tour de toile doit être
maintenu sur le cylindre. Cet écran est doté de
série d'une bande noire supérieure de 0 cm (0 po)
ou 5 cm (2 po). Consultez la fiche technique pour
plus de renseignements.

Less Screen Drop

1. Raise picture surface approximately two feet above

desired level.

2. Place operating switch in “off” position.

3. Turn the “down” limit switch (Fig. 2) one-quarter turn

clockwise. Test by raising picture surface
approximately two feet, then lower again. Repeat
until desired picture surface position is attained.

CAUTION: Adjusting the down limit switch for less

drop by more than 6" can cause the screen

surface to lose proper tensioning.

ATTENTION! LE FAIT D'AJOUTER NE DÉROULEZ

PAS TROP L'ÉCRAN PLUS DE 15 CM (6PO) AUX

INTERRUPTEURS DE FIN DE COURSE PEUT

FAIRE PERDRE LA BONNE TENSION À LA

SURFACE DE L'ÉCRAN.

SCREEN ADJUSTMENT

«
...
5
6
7
8
9
...
»

Summary of Contents for DA-LITE Tensioned Advantage Series






























































Reviews:

No comments

Related manuals for DA-LITE Tensioned Advantage Series

SX50 - REALiS SXGA+ LCOS Projector

Brand: Canon Pages: 66

Brand: Canon Pages: 28

Digital Walldisplay 9000PD Plus

Brand: 3M Pages: 12

Brand: ACCO Brands Pages: 31

Brand: Acer Pages: 62

Brand: Acer Pages: 58

S1370WHn Series

Brand: Acer Pages: 64

Brand: Acer Pages: 140

Brand: Acer Pages: 126

Brand: Acer Pages: 2

Brand: Sim2 Pages: 31

Brand: Panchromatic Pages: 27

Brand: SHOWTEC Pages: 36

Brand: HQ Power Pages: 12

BrilliantColorPanel BCP100

Brand: ViewSonic Pages: 2

Brand: Yaber Pages: 29

Brand: Panasonic Pages: 72

Brand: Panasonic Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands