LEGRAND DA-LITE Tensioned Advantage Series User Manual Download

Page: 25 / 61

SYMPTOM

CAUSE

SOLUTION

Screen will not operate
and motor does not hum.

Incorrect line voltage.

Verify 115-125V (or 220-240V). If insufficient voltage,
rewire incoming electric line.

Blown fuse.

Replace fuse.

Tripped circuit breaker.

Reset circuit breaker.

No power to operating switch
or junction.

Check above. Tighten all loose wire connections.
Correct any improper connections.

Down Position
Check for power across black and white leads.

Up Position
Check for power across red and white leads.

Screen will not operate
and motor does not hum.

Power at junction box.

Thermal overload tripped.

Let motor cool down for 15 minutes. Try again.

Broken wire in the “down” or “up” position.

Check for continuity. Cut off old splice and reconnect.

Defective motor, limit switch or capacitor.

Replace motor assembly. NOTE: Motor is a sealed
assembly.

Capacitor burned out.

Replace motor assembly.

Screen does not stop
at correct position.

Limit switch out of adjustment.

See Screen Adjustment section.

Noise.

NOTE: Screen will

operate

with a low pitched hum.

Squeaking, rubber end plug rubbing on motor.

Center roller in case.

Grinding. Foreign object in screen
rubbing on roller or fabric.

Remove.

Gear noise.

Replace motor assembly.

Coasting.

Defective brake.

Replace motor assembly.

Fabric hangs crooked.

Screen not installed properly.

Check for level and plumb.

Fabric has backed up inside case.

Adjust “down” limit switch slowly until roller is exposed
and wrinkle comes out, then readjust for proper drop.

Fabric is damaged.

Replace fabric.

TROUBLESHOOTING

Summary of Contents for DA-LITE Tensioned Advantage Series






























































Search results

Summary of Contents for DA-LITE Tensioned Advantage Series

Reviews:

Related manuals for DA-LITE Tensioned Advantage Series

Brands by name

Popular brands

LEGRAND DA-LITE Tensioned Advantage Series, User Manual

Search results

Summary of Contents for DA-LITE Tensioned Advantage Series

Reviews:

Related manuals for DA-LITE Tensioned Advantage Series

Brands by name

Popular brands