LEGRAND DA-LITE Tensioned Advantage Series User Manual Download Page 5 | Manualshive

Page: 5 / 61

background image

5

1. The case provides multiple attachment points for

bolts, cables, or threaded rod. Page 7 shows
threaded rod installed. The variable position-
mounting bracket may be located anywhere along
the length of the case. It is recommended to keep the
brackets spaced evenly enough to distribute the
weight of the screen.

The case has a self-trimming flange around the

bottom. Ceiling tiles or drywall may be placed on top
of this flange to provide a finished appearance.

2. After securing the case in the ceiling check that the

case is level and plumb.

3. Use supplied 1/8" hex key and a 1/4" wrench to

remove silver shipping brackets attached to slat and
screen case.

4. Install electrical connections that apply to your unit.

Refer to the following diagrams for proper
installation. The terminal block for the wall switch
connections is located under the metal housing
surrounding the junction box. Remove two screws
for access.

NOTE: Use provided knockouts for all electrical
connections. DO NOT drill additional holes into
screen case or end cap.

1. Carefully unpack screen and remove outer wrapping

from case.

2. Make sure to recheck measurements of screen

location before installation.

Figure 1

Fabric Door

Access

Door

Screw For Securing

Roller Access Door

Knockouts For

Conduit Installation

PRE-INSTALLATION

CASE INSTALLATION

«
...
3
4
5
6
7
...
»

Summary of Contents for DA-LITE Tensioned Advantage Series






























































Reviews:

No comments

Related manuals for DA-LITE Tensioned Advantage Series

BarcoReality 908

Brand: Barco Pages: 4

Brand: Barco Pages: 2

Brand: Barco Pages: 50

Brand: ACCO Brands Pages: 33

UVONIX BLACKSTAR

Brand: Blizzard Lighting Pages: 16

Brand: ViewSonic Pages: 54

Brand: Hitachi Pages: 92

Brand: Hitachi Pages: 162

Brand: Hitachi Pages: 99

Brand: Hitachi Pages: 72

50V720 - 50" Rear Projection TV

Brand: Hitachi Pages: 72

Brand: Hitachi Pages: 60

Brand: Hitachi Pages: 80

Brand: Hitachi Pages: 88

Brand: Hitachi Pages: 84

Brand: Hitachi Pages: 68

Brand: Hitachi Pages: 64

50VS810 - 50" Rear Projection TV

Brand: Hitachi Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands